What We Do?

Concrete Mix Designs and PSI Explained

Most people ordering concrete know roughly what they are pouring but not what to ask for. Concrete mix designs are the recipe behind the load: the strength, the consistency, the aggregate size and the admixtures that together decide how the concrete behaves at the chute and how it performs for the next thirty years.

This page explains what those numbers mean in plain terms so you can specify a mix with confidence. Southern Readymix batches from eight plants across Georgia, and dispatch will confirm the right mix for your pour when you order.

This page covers the concrete mix designs we batch most often and what each specification actually controls once the truck reaches your forms.

This page covers the concrete mix designs we batch most often and what each specification actually controls once the truck reaches your forms.

Standard Strength Mixes

3000 and 2500 psi are the two concrete mix designs we batch most often, and we produce the full range of strengths above and below them to spec.

Four Inch Average Slump

Four inches is our average slump. Loads are slumped at the plant unless you ask for something different before the truck leaves.

57 Stone and 89 Stone

We stock 57 stone as the standard coarse aggregate and 89 stone for tight forms, thin sections and congested reinforcement.

Air Entrainment and Admixtures

We stock 57 stone and 89 stone, so concrete mix designs can be adjusted for tight forms, thin sections and congested reinforcement.

Reading a Spec

What PSI Measures in Concrete Mix Designs

PSI is pounds per square inch, and it describes compressive strength. It is measured by casting cylinders from the load and crushing them in a lab, conventionally at 28 days, which is when concrete is treated as having reached its design strength. It carries on gaining strength slowly after that.

A higher number is not automatically better. Strength is chosen to suit the loading and the exposure, and specifying far above what a job needs adds cost without adding useful performance. What matters is matching the mix to the work.

Understanding psi is the first step in reading concrete mix designs, because strength is the number every other decision is built around.

Choosing a Strength

Which Mix Suits Which Pour

Across our eight plants the two mixes that leave the yard most often are 3000 psi and 2500 psi. Between them they cover the large majority of residential work. That does not limit what we batch: strengths above and below are produced to order, so a 4000 or 4500 psi commercial pour is an ordinary request rather than a special one.

2500 psi suits non-structural work where load is light and the concrete is mainly filling a shape: sidewalks, small pads, fence post and mailbox footings, and general fill.

3000 psi is the everyday residential workhorse. Footings, foundation walls, garage and basement slabs, patios and most driveways are specified at 3000 unless plans say otherwise.

3500 to 4000 psi is where driveways carrying heavier vehicles, structural slabs and commercial flatwork usually sit. 4500 psi and above covers structural columns, beams, industrial floors and anything where the engineer has run the numbers and put a figure on the drawings.

For residential work we use standard mix designs that are proven across the trade area. Commercial and specified jobs are batched to the mix design supplied for that job. We do not publish our mix designs, so if your specification requires submittals, ask dispatch when you order and we will get the right documentation to you.

These are the concrete mix designs we batch most often, and the strength you choose should follow the load the concrete will carry rather than habit.

Slump and Aggregate

Slump, Stone Size and Concrete Mix Designs in Practice

Slump describes how far fresh concrete settles under its own weight, measured in inches, and it is the practical shorthand for how the mix will handle. Our average slump is around four inches, which pours and finishes well for typical flatwork and footings. Loads are slumped at the plant before the truck leaves unless you ask for something different, so tell dispatch when you order rather than after the truck arrives.

A stiffer mix at two or three inches holds its shape on slopes and resists segregation. A wetter mix at five or six inches flows into congested reinforcement and narrow forms more readily. Neither is better in the abstract; they suit different pours.

What does damage strength is water added at the site. Every extra gallon dilutes the cement paste, and concrete that arrives at 3000 psi can finish well below it after a crew has hosed the drum to make the pour easier. If a load needs to move more freely, a water reducer or plasticizer increases slump without adding water and without losing strength, and we can batch either on request.

Aggregate size is the other half of placement. We stock 57 stone, the standard coarse aggregate for most slabs, footings and driveways, and 89 stone, a smaller aggregate that suits thin sections, tight forms and heavily congested rebar where 57 would bridge. Smaller stone generally needs more paste, which is worth knowing before it is specified across a large pour.

Slump and aggregate are the two variables that change how concrete mix designs behave in the forms, even when the strength stays the same.

Two concrete mix designs at the same strength can behave very differently in the forms once slump and aggregate change, which is why both belong on the order.

Two concrete mix designs at the same strength can behave very differently in the forms once slump and aggregate change, which is why both belong on the order.

Where Quality Meets Consistency

Specifying a Mix With Southern Readymix

When you call dispatch, five things settle the mix: the volume in cubic yards, the strength in psi, the slump you want, the aggregate if the job calls for something other than 57 stone, and any admixture the pour or the weather requires.

We can batch accelerator to bring set time forward in cold weather, retarder to hold a load open in summer heat or on a long placement, and water reducer or plasticizer to raise workability without adding water. Air-entrained mixes are available where freeze-thaw exposure or a specification calls for them.

If your plans carry a specification, read us the line and we will match it. If they do not, tell dispatch what you are pouring and how thick, and we will suggest a strength and slump that suits the work. Standard residential designs are already proven across the trade area; commercial jobs are batched to the design supplied for that job.

Everything is batched at our eight Georgia plants in Locust Grove, Hampton, Jackson, Covington, Madison, Zebulon, Luthersville and Auburn. Call 770-914-9700 or use the contact form. See also short load delivery for pours under seven yards, fiber reinforced concrete, and the concrete calculator for sizing.

For background on cement chemistry and how concrete mix designs are developed, the Portland Cement Association publishes technical resources for specifiers. For what we can batch in Georgia, dispatch is the quicker answer.

Our standard residential concrete mix designs are proven across the trade area, and commercial jobs are batched to the design supplied for that job.

Tell dispatch what you are pouring and we will match it to one of our concrete mix designs, or batch to the design your plans specify.

Tell dispatch what you are pouring and we will match it to one of our concrete mix designs, or batch to the design your plans specify.